Price: £9.38 - £7.97 (as of Jun 06, 2025 12:08:29 UTC – Details)
This is a perfect skill exercise materials for beginners. Package includes: 1. PCB blank: 1 PC board (82 mm x 60 mm). 2. 0805 resistors: 30 pieces. 3. 0603 Resistors:10pcs 4. 0603 8pin resistor network: 7 parts. 5. 0805 capacitors: 14 pieces. 6. 3216 Diodes:6pcs 7. SOT-23 transistors: 6 pieces. 8. SO14 IC:2pcs 9. LQFP44 IC: 2pcs
This is a good soldering skills training materials for beginners Beginner DIY SMD/SMT Components Practice Board Soldering Skill Training Set
9 reviews for Gikfun Beginners DIY SMD/SMT Components Practice Board Soldering Skill Training Kit ae1173
0.0out of 5
★★★★★
0
★★★★★
0
★★★★★
0
★★★★★
0
★★★★★
0
Write a review
Show allMost HelpfulHighest RatingLowest Rating
Martin G. Taft –
Good kit for smd practice
This was my first venture into smd soldering and gave me the practice and confidence to build a digital clock and fm radio kits afterwards.
Helpful(0)Unhelpful(0)You have already voted this
Kevin Darling –
Practice board
excellent board for practicing with. Worked well in my recently acquired “Reflow Oven”
Helpful(0)Unhelpful(0)You have already voted this
Gryptype –
A good little practise kit that does nothing
I fancied giving teeny weeny SMDs a more serious go so this was perfect.I’ve done a little bit before with smaller projects; the odd resistor or capacitor here and there, but this gives you a reasonable range of components to play with.You get resistors / resistor blocks, capacitors, square and straight ICs, transistors, and diodes. This PCB does absolutely nothing useful when populated, so it’s fine to undo and retry without worrying about damaging anything.It does however have convenient points scattered about for you to test continuity from the ICs, and you can always test the resistance and capacitance wherever you fancy.For £7? Bargain!
Helpful(0)Unhelpful(0)You have already voted this
WARRIOR 074. –
Small componts.
Very good.
Helpful(0)Unhelpful(0)You have already voted this
Mark Story –
A good practice kit with a variety of components and sizes. There are lots of 0805 components to practice with and a few big chips too. I appreciate the bare pads that can be use to test continuity once you’re done a block of components.
Helpful(0)Unhelpful(0)You have already voted this
Fred Raimer –
Excellent quality kit that has various surface-mounted components to learn and practice soldering skills. It took me some time to learn, and it withstood repeated soldering on and off to become good enough to attempt a repair on my vintage Macs.A very low price for what you get and really does what I needed. Highly recommend.
Helpful(0)Unhelpful(0)You have already voted this
Amazon Kunde –
Mein Sohn liebt das löten.Jederzeit wieder
Helpful(0)Unhelpful(0)You have already voted this
Sergio Medina –
Bueno Par aprender
Helpful(0)Unhelpful(0)You have already voted this
Steve Cross –
If you have had at least some experience with electronic soldering on larger, traditional through hole components but want to try your hand at SMD, then this is a great way to get started. This is a very high quality kit with a good assortment of different size parts to practice on. And very reasonably priced. For about the price of a movie, you canât go wrong. And even if you make a few mistakes along the way while you are learning, it doesnât matter because the kit was never intended to do anything constructive except teach you how to solder SMD joints.Having said that, it DOES offer some useful ways to check the quality of your work. If you hold the board up to a strong light, you can see the circuit trace patterns and use them to make some tests with a volt/ohm meter. For example, on the right side of the board, resistors 1-10 are connected in series and there are a couple of test points near R7 and R8 that you can use to check continuity on all 10 resistors at one time. Other test points connect to more complicated combinations of series and parallel networks and you will have to break out the calculator to figure out what the correct resistance, capacitance, etc. SHOULD be, but this is all stuff you need to know anyway if you ever intend to do troubleshooting on electronic circuits.
Martin G. Taft –
Good kit for smd practice
This was my first venture into smd soldering and gave me the practice and confidence to build a digital clock and fm radio kits afterwards.
Kevin Darling –
Practice board
excellent board for practicing with. Worked well in my recently acquired “Reflow Oven”
Gryptype –
A good little practise kit that does nothing
I fancied giving teeny weeny SMDs a more serious go so this was perfect.I’ve done a little bit before with smaller projects; the odd resistor or capacitor here and there, but this gives you a reasonable range of components to play with.You get resistors / resistor blocks, capacitors, square and straight ICs, transistors, and diodes. This PCB does absolutely nothing useful when populated, so it’s fine to undo and retry without worrying about damaging anything.It does however have convenient points scattered about for you to test continuity from the ICs, and you can always test the resistance and capacitance wherever you fancy.For £7? Bargain!
WARRIOR 074. –
Small componts.
Very good.
Mark Story –
A good practice kit with a variety of components and sizes. There are lots of 0805 components to practice with and a few big chips too. I appreciate the bare pads that can be use to test continuity once you’re done a block of components.
Fred Raimer –
Excellent quality kit that has various surface-mounted components to learn and practice soldering skills. It took me some time to learn, and it withstood repeated soldering on and off to become good enough to attempt a repair on my vintage Macs.A very low price for what you get and really does what I needed. Highly recommend.
Amazon Kunde –
Mein Sohn liebt das löten.Jederzeit wieder
Sergio Medina –
Bueno Par aprender
Steve Cross –
If you have had at least some experience with electronic soldering on larger, traditional through hole components but want to try your hand at SMD, then this is a great way to get started. This is a very high quality kit with a good assortment of different size parts to practice on. And very reasonably priced. For about the price of a movie, you canât go wrong. And even if you make a few mistakes along the way while you are learning, it doesnât matter because the kit was never intended to do anything constructive except teach you how to solder SMD joints.Having said that, it DOES offer some useful ways to check the quality of your work. If you hold the board up to a strong light, you can see the circuit trace patterns and use them to make some tests with a volt/ohm meter. For example, on the right side of the board, resistors 1-10 are connected in series and there are a couple of test points near R7 and R8 that you can use to check continuity on all 10 resistors at one time. Other test points connect to more complicated combinations of series and parallel networks and you will have to break out the calculator to figure out what the correct resistance, capacitance, etc. SHOULD be, but this is all stuff you need to know anyway if you ever intend to do troubleshooting on electronic circuits.